Where to find 400 101 dumps

Act now and download your Cisco ccie 400 101 dumps test today! Do not waste time for the worthless Cisco passleader 400 101 tutorials. Download Up to the immediate present Cisco CCIE Routing and Switching (v5.0) exam with real questions and answers and begin to learn Cisco 400 101 ccie with a classic professional.

This Testaimer.com web site will certainly provide you with credible info concerning 400-101 exam dumps.

Q311. Refer to the exhibit. The Main1 and Branch1 switches are connected directly over an MPLS pseudowire, and both run UDLD. After router B1 reloads because of a power failure, the pseudowire is restored. However, the Branch1 switch is unable to reach the Main1 switch. 

Which two actions can you take to restore connectivity and prevent the problem from recurring? (Choose two.) 

A. Configure a backup pseudowire between the Main1 and Branch1 switches. 

B. Enable UDLD recovery on both the Main1 and Branch1 switches. 

C. Configure a backup GRE tunnel between the Main1 and Branch1 switches. 

D. Enable errdisable recovery on both the Main1 and Branch1 switches. 

E. Issue the shutdown and no shutdown commands on both the Branch1 switch’s uplink to the B1 router and the Main1 switch’s uplink to the M1 router. 

F. Issue the shutdown and no shutdown commands on the Branch1 switch uplink to the B1 router only. 

Answer: D,F 

Q312. Which two statements are true about IPv6 multicast? (Choose two.) 

A. Receivers interested in IPv6 multicast traffic use IGMPv6 to signal their interest in the IPv6 multicast group. 

B. The PIM router with the lowest IPv6 address becomes the DR for the LAN. 

C. An IPv6 multicast address is an IPv6 address that has a prefix of FF00::/8. 

D. The IPv6 all-routers multicast group is FF02:0:0:0:0:0:0:2. 

Answer: C,D 


Multicast addresses in IPv6 have the prefix ff00::/8. 

Well-known IPv6 multicast addresses 




All nodes on the local network segment 


All routers on the local network segment 

Reference: http://en.wikipedia.org/wiki/Multicast_address 


Drag and drop the events on the left to dispaly the correct sequence on the right when CoPP is enabled. 



Drag and drop each policy command on the left to the function it performs on the right. 


Q315. Which two OSPF LSA types are flooded within the originating area? (Choose two.) 

A. type 1, Router LSA 

B. type 2, Network LSA 

C. type 3, Network Summary LSA 

D. type 4, ASBR Summary LSA 

E. type 6, Group Membership LSA 

F. type 9, Opaque LSA 

Answer: A,B 


OSPF relies on several types of Link State Advertisements (LSAs) to communicate link state information between neighbors. A brief review of the most applicable LSA types: 

. Type 1 - Represents a router 

. Type 2 - Represents the pseudonode (designated router) for a multiaccess link 

. Type 3 - A network link summary (internal route) 

. Type 4 - Represents an ASBR 

. Type 5 - A route external to the OSPF domain 

. Type 7 - Used in stub areas in place of a type 5 LSA LSA types 1 and 2 are found in all areas, and are never flooded outside of an area. They are only flooded within the area that they originated from. 

Reference: http://packetlife.net/blog/2008/jun/24/ospf-area-types/ 

Q316. Which statement describes the native VLAN concept in an ISL trunk? 

A. It is the VLAN ID that is assigned to untagged packets. 

B. It is the VLAN with highest priority. 

C. It is the default VLAN for a trunk. 

D. There is no native VLAN concept in an ISL trunk. 



ISL has no native VLAN concept because it places the entire Ethernet frame in the payload of an ISL frame. Native VLANs is an 802.1Q specific concept 


Drag and drop the DMVPN command on the left to the corresponding function on the right. 


Q318. Which two protocols are used to establish IPv6 connectivity over an MPLS network? (Choose two.) 

A. 6PE 

B. 6VPE 




F. IPv6IP 

Answer: A,B 

Q319. Which two types of traffic are blocked when the storm control threshold for multicast traffic is reached on a port? (Choose two.) 






Answer: B,D 

Q320. What two values are required to implement an EIGRP named configuration? (Choose two.) 

A. virtual-instance-name 

B. address-family 

C. router-id 

D. subnet-mask 

E. process-id 

Answer: A,B 

400-101 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

Get it now →