Top Breathing 200-401 torrent Tips!

200-401 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

Want to know Pass4sure 200-401 Exam practice test features? Want to lear more about Cisco Managing Industrial Networks with Cisco Networking Technologies certification experience? Study Best Quality Cisco 200-401 answers to Up to the immediate present 200-401 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 200-401 (Managing Industrial Networks with Cisco Networking Technologies) test on your first attempt.

This web site will certainly provide you with credible info concerning 200-401 exam dumps

Q11. - (Topic 4) 

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid green? 

A. The port is sending or receiving data. 

B. A link is present. 

C. No link is present. 

D. There is a link fault. 

E. The port is not forwarding. 


Q12. - (Topic 2) 


Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation? 

A. a router with two Ethernet interfaces 

B. a switch with two Ethernet interfaces 

C. a router with one Ethernet and one serial interface 

D. a switch with one Ethernet and one serial interface 

E. a router with one Ethernet and one modem interface 


Q13. - (Topic 2) 

Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.) 

A. designated ports 

B. duplex operating mode 

C. fast mode ports 

D. root bridge 

E. root ports 

F. BDPU priority 

Answer: A,D,E 

Q14. - (Topic 4) 

What are two symptoms of duplex mismatch? (Choose two.) 

A. Ping does not return from one direction versus the other direction. 

B. Communication is slow and locks up. 

C. Speed is seen equally slow in both directions. 

D. The half-duplex side sees frame sequence errors or runt frames. 

E. The full-duplex side sees CRC errors. 

Answer: B,D 

Q15. - (Topic 5) 

How does the optical time domain reflectometer use "backscattered" light to make measurements? 

A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems. 

B. It performs wiremapping to measure that all pins are correctly connected. 

C. It correlates the returned light pulses with a location in the fiber. 

D. It measures light-pulse width to measure that all pins are correctly connected. 


Q16. DRAG DROP - (Topic 2) 


Q17. - (Topic 4) 

An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the switch port link LED turns green. The link light indicates what two conditions? (Choose two.) 

A. Layer 2 communication has been established between the PC and switch. 

B. The PC has received a DHCP address. 

C. Traffic is being sent from the switch to the PC. 

D. If flashing, the green LED indicates port speed of 100 Mb/s. 

E. The Layer 1 media is functioning between the PC and switch. 

F. The switch port is functioning as a half-duplex connection. 

Answer: A,E 

Q18. - (Topic 5) 

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used? 

A. hop count 

B. administrative distance 

C. link bandwidth 

D. link delay 

E. link cost 


Q19. - (Topic 2) 

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.) 

A. the size of the infrastructure 

B. the complexity of the infrastructure 

C. the age of the infrastructure 

D. the industry that the infrastructure supports 

E. the physical environment of the infrastructure 

Answer: A,B 

Q20. - (Topic 4) 

A network administrator has subnetted the network using a subnet mask of A duplicate IP address of has accidentally been configured on a workstation in the network. The technician on the plant floor must assign this workstation a new IP address within that same subnetwork. Which address should be assigned to the workstation?