Advanced Guide: 300 101 route pdf

300-101 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

https://www.2passeasy.com/dumps/300-101/

Proper study guides for Far out Cisco ROUTE Implementing Cisco IP Routing certified begins with Cisco 300 101 pdf preparation products which designed to deliver the High value ccnp 300 101 pdf questions by making you pass the route 300 101 test at your first time. Try the free 300 101 route demo right now.


This Testaimer.com web site will certainly provide you with credible info concerning 300-101 exam dumps

P.S. High value 300-101 study guides are available on Google Drive, GET MORE: https://drive.google.com/open?id=1BHb398qwKUUDgc3Vdghj3SxO9n6grhvU


New Cisco 300-101 Exam Dumps Collection (Question 14 - Question 23)

New Questions 14

Router E is configured with the EIGRP variance 2 command.

What path will Router E take to reach Router A?

A. only E-D-A

B. only E-B-A

C. only E-C-A

D. both E-B-A and E-C-A

E. both E-B-A and E-D-A

F. all available paths.

Answer: D

Explanation:

By using the u201cvariance 2 command we can share traffic to other feasible successor routes. But by default, EIGRP only shares traffic to 4 paths. So we need to use the u201cmaximum- paths 6 to make sure all of these routes are used.


New Questions 15

For security purposes, an IPv6 traffic filter was configured under various interfaces on the local router. However, shortly after implementing the traffic filter, OSPFv3 neighbor adjacencies were lost. What caused this issue?

A. The traffic filter is blocking all ICMPv6 traffic.

B. The global anycast address must be added to the traffic filter to allow OSPFv3 to work properly.

C. The link-local addresses that were used by OSPFv3 were explicitly denied, which caused the neighbor relationships to fail.

D. IPv6 traffic filtering can be implemented only on SVIs.

Answer: C


New Questions 16

Refer to the exhibit.

Which one statement is true?

A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.

B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the 10.0.0.0/8 network is missing from Router B.

C. The 10.0.0.0/8 network will not be in the routing table on Router B.

D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but users on the 192.168.5.0/24 cannot successfully ping users on the 10.0.0.0/8 network.

E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.

Answer: E


New Questions 17

Which common issue causes intermittent DMVPN tunnel flaps?

A. a routing neighbor reachability issue

B. a suboptimal routing table

C. interface bandwidth congestion

D. that the GRE tunnel to hub router is not encrypted

Answer: A


New Questions 18

Which two technologies can encapsulate an IPv6 payload in an IPv4 packet for transmission across a network? (Choose two)

A. L2TPv3

B. trunking

C. AToM

D. ISATAP

E. NAT-PT

Answer: D,E


New Questions 19

CORRECT TEXTYou are a network engineer with ROUTE.com, a small IT company. They have recently merged two organizations and now need to merge their networks as shown in the topology exhibit. One network is using OSPF as its IGP and the other is using EIGRP as its IGP. R4 has been added to the existing OSPF network to provide the interconnect between the OSPF and EIGRP networks. Two links have been added that will provide redundancy.

The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that provides the greatest bandwidth. The redundant paths from the OSPF network to the EIGRP network must be available in case of a link failure. No static or default routing is allowed in either network.

A previous network engineer has started the merger implementation and has successfully assigned and verified all IP addressing and basic IGP routing. You have been tasked with completing the implementation and ensuring that the network requirements are met. You may not remove or change any of the configuration commands currently on any of the routers. You may add new commands or change default values.

Answer:

First we need to find out 5 parameters (Bandwidth, Delay, Reliability, Load, MTU)

of the s0/0/0 interface (the interface of R2 connected to R4) for redistribution:

R2#show interface s0/0/0

Write down these 5 parameters, notice that we have to divide the Delay by 10 because the metric unit is in tens of microsecond. For example, we get Bandwidth=1544 Kbit, Delay=20000 us, Reliability=255, Load=1, MTU=1500 bytes then we would redistribute as follows:

R2#config terminal R2(config)# router ospf 1

R2(config-router)# redistribute eigrp 100 metric-type 1 subnets R2(config-router)#exit

R2(config-router)#router eigrp 100

R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500

Note: In fact, these parameters are just used for reference and we can use other parameters with no problem.

If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000) For R3 we use the show interface fa0/0 to get 5 parameters too

R3#show interface fa0/0

For example we get Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500 bytes

R3#config terminal R3(config)#router ospf 1

R3(config-router)#redistribute eigrp 100 metric-type 1 subnets R3(config)#exit

R3(config-router)#router eigrp 100

R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500

Finally you should try to u201cshow ip routeu201d to see the 172.16.100.1 network (the network behind R4) in the routing table of R1 and make a ping from R1 to this network.

Note: If the link between R2 and R3 is FastEthernet link, we must put the command below under EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4), which is better than R1 -> R2 -> R4.

R2(config-router)# distance eigrp 90 105

This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP external routes to 105, which is smaller than the Administrative Distance of OSPF

(110) -> the link between R2 & R3 will be preferred to the serial link between R2 & R4. Note: The actual OPSF and EIGRP process numbers may change in the actual exam so be sure to use the actual correct values, but the overall solution is the same.


New Questions 20

Which three steps are most helpful in verifying proper route redistribution? (Choose three.)

A. On the routers not performing the route redistribution, use the show ip route command to see if the redistributed routes show up.

B. On the ASBR router performing the route redistribution, use the show ip protocol command to verify the redistribution configurations.

C. On the ASBR router performing the route redistribution, use the show ip route command to verify that the proper routes from each routing protocol are there.

D. On the routers not performing the route redistribution, use the show ip protocols command to verify the routing information sources.

E. On the routers not performing the route redistribution, use the debug ip routing command to verify the routing updates from the ASBR.

Answer: A,B,C

Explanation:

In order to verify proper route redistribution, use the u201cshow ip routeu201d command on all routers within the network, as well as the ABSR, to verify that the routes are properly being advertised to all routers. In addition, issuing the u201cshow ip protocolu201d can be used on the router performing the redistribution to verify that routes are being redistributed into each other.


New Questions 21

A network engineer has been asked to ensure that the PPPoE connection is established and authenticated using an encrypted password. Which technology, in combination with PPPoE, can be used for authentication in this manner?

A. PAP

B. dot1x

C. IPsec

D. CHAP

E. ESP

Answer: D


New Questions 22

Which three statements are true when configuring redistribution for OSPF? (Choose three)

A. The default metric is 10.

B. The default metric is 20.

C. The default metric type is 2.

D. The default metric type is 1.

E. Subnets do not redistribute by default.

F. Subnets redistribute by default.

Answer: B,C,E


New Questions 23

What is the purpose of the autonomous-system {autonomous-system-number} command?

A. It sets the EIGRP autonomous system number in a VRF.

B. It sets the BGP autonomous system number in a VRF.

C. It sets the global EIGRP autonomous system number.

D. It sets the global BGP autonomous system number.

Answer: A


100% Far out Cisco 300-101 Questions & Answers shared by Dumpscollection, Get HERE: http://www.dumpscollection.net/dumps/300-101/ (New 745 Q&As)