cbt nuggets ccnp 300-115 download (61 to 70)

300-115 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

https://www.2passeasy.com/dumps/300-115/

Exam Code: 300-115 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Implementing Cisco IP Switched Networks
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 300-115 Exam.

2016 May 300-115 Study Guide Questions:

Q61. What does the command vlan dot1q tag native accomplish when configured under global

configuration?

A. All frames within the native VLAN are tagged, except when the native VLAN is set to 1.

B. It allows control traffic to pass using the non-default VLAN.

C. It removes the 4-byte dot1q tag from every frame that traverses the trunk interface(s).

D. Control traffic is tagged.

Answer: D


Q62. After the implementation of several different types of switches from different vendors, a network engineer notices that directly connected devices that use Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could be used to resolve this issue?

A. Local Area Mobility

B. Link Layer Discovery Protocol

C. NetFlow

D. Directed Response Protocol

Answer: B


Q63. which feature is automatically enabled when a voice VLAN is configured, but not automatically disabled when a voice VLAN is removed?

A. portfast

B. port-security

C. spanning tree

D. storm control

Answer: A


300-115  practice test

Updated peavey max 115 1x15 300-watt bass combo:

Q64. Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRP to provide a high availability solution.

DSW1 -primary device for VLAN 101 VLAN 102 and VLAN 105

DSW2 - primary device for VLAN 103 and VLAN 104

A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.

Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.

During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1 and DSW2. All other interfaces were up. During this time, DSW1 became the active router for the VLAN 104HSRP group. As related to the VLAN 104HSRP group, what can to be done to make the group function properly?

A. On DSW1, disable preempt.

B. On DSW2 decrease the priority value to a value less than 150.

C. On DSW1, increase the decrement value in the track command to a value greater than 6.

D. On DSW1, decrease the decrement value in the track command to a value less than 1.

Answer: C



Q65. After implementing VTP, the extended VLANs are not being propagated to other VTP switches. What should be configured for extended VLANs?

A. VTP does not support extended VLANs and should be manually added to all switches.

B. Enable VTP version 3, which supports extended VLAN propagation.

C. VTP authentication is required when using extended VLANs because of their ability to cause network instability.

D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.

Answer: B


Q66. Refer to the exhibit.


Which option describes the reason for this message in a GLBP configuration?

A. Unavailable GLBP active forwarder

B. Incorrect GLBP IP address

C. HSRP configured on same interface as GLBP

D. Layer 2 loop

Answer: D


2passeasy.com

Real cbt nuggets ccnp switch 300-115:

Q67. Refer to the exhibit.


A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)

A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination

B. A remote SPAN VLAN on the distribution and access layer switch

C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination

D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination

E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination

F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination

Answer: BCD


Q68. What is required for a LAN switch to support 802.1q Q-in-Q encapsulation?

A. Support less than 1500 MTU

B. Support 1504 MTU or higher

C. Support 1522 layer 3 IP and IPX packet

D. Support 1547 MTU only

Answer: B


Q69. A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?

A. Reload the new switch.

B. Restart the VTP process on the new switch.

C. Reload the VTP server.

D. Verify connected trunk ports.

Answer: D


Q70. A new network that consists of several switches has been connected together via trunking interfaces. If all switches currently have the default VTP domain name "null", which statement describes what happens when a domain name is configured on one of the switches?

A. The switch with the non-default domain name restores back to "null" upon reboot.

B. Switches with higher revision numbers does not accept the new domain name.

C. VTP summary advertisements are sent out of all ports with the new domain name.

D. All other switches with the default domain name become VTP clients.

Answer: C



see more Implementing Cisco IP Switched Networks