What to do with cbt nuggets 300-115

300-115 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

https://www.2passeasy.com/dumps/300-115/

Cause all that matters here is passing the Cisco 300-115 exam. Cause all that you need is a high score of 300-115 Implementing Cisco IP Switched Networks exam. The only one thing you need to do is downloading Testking 300-115 exam study guides now. We will not let you down with our money-back guarantee.

2016 Jun cbt nuggets ccnp switch 300-115:

Q81. For security reasons, the IT manager has prohibited users from dynamically establishing trunks with their associated upstream switch. Which two actions can prevent interface trunking? (Choose two.)

A. Configure trunk and access interfaces manually.

B. Disable DTP on a per interface basis.

C. Apply BPDU guard and BPDU filter.

D. Enable switchport block on access ports.

Answer: A,B


Q82. Which statement about Cisco devices learning about each other through Cisco Discovery Protocol is true?

A. Each device sends periodic advertisements to multicast address 01:00:0C:CC:CC:CC.

B. Each device broadcasts periodic advertisements to all of its neighbors.

C. Each device sends periodic advertisements to a central device that builds the network topology.

D. Each device sends periodic advertisements to all IP addresses in its ARP table.

Answer: A


Q83. Which command globally enables AAA on a device?

A. aaa new-model

B. aaa authentication

C. aaa authorization

D. aaa accounting

Answer: A


Q84. An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?

A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.

B. Adjust the EtherChannel load-balancing method based on destination IP addresses.

C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.

D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.

E. Adjust the EtherChannel load-balancing method based on source IP addresses.

Answer: E


Q85. Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?

A. sticky

B. dynamic

C. static

D. secure

Answer: A


300-115  latest exam

Most up-to-date 9tut ccnp 300-115:

Q86. Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)

A. LACP system priority

B. LACP port priority

C. interface MAC address

D. system ID

E. port number

F. hot-standby link identification number

G. interface bandwidth

Answer: ABDE


Q87. Refer to the exhibit.


Users of PC-1 experience slow connection when a webpage is requested from the server. To increase bandwidth, the network engineer configured an EtherChannel on interfaces Fa1/0 and Fa0/1 of the server farm switch, as shown here:

Server_Switch#sh etherchannel load-balance EtherChannel Load-Balancing Operational State (src-mac): Non-IP: Source MAC address

IPv4: Source MAC address IPv6: Source IP address Server_Switch#

However, traffic is still slow. Which action can the engineer take to resolve this issue?

A. Disable EtherChannel load balancing.

B. Upgrade the switch IOS to IP services image.

C. Change the load-balance method to dst-mac.

D. Contact Cisco TAC to report a bug on the switch.

Answer: C


Q88. Refer to the exhibit.


Which set of configurations will result in all ports on both switches successfully bundling into an EtherChannel?

A. switch1

channel-group 1 mode active switch2

channel-group 1 mode auto

B. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode passive

C. switch1

channel-group 1 mode on switch2

channel-group 1 mode auto

D. switch1

channel-group 1 mode desirable switch2

channel-group 1 mode auto

Answer: D


Q89. In a Cisco switch, what is the default period of time after which a MAC address ages out and is discarded?

A. 100 seconds

B. 180 seconds

C. 300 seconds

D. 600 seconds

Answer: C


Q90. A Cisco Catalyst switch that is prone to reboots continues to rebuild the DHCP snooping database. What is the solution to avoid the snooping database from being rebuilt after every device reboot?

A. A DHCP snooping database agent should be configured.

B. Enable DHCP snooping for all VLANs that are associated with the switch.

C. Disable Option 82 for DHCP data insertion.

D. Use IP Source Guard to protect the DHCP binding table entries from being lost upon rebooting.

E. Apply ip dhcp snooping trust on all interfaces with dynamic addresses.

Answer: A



see more Implementing Cisco IP Switched Networks